DuPont Chain Saver-Saver – Wax Based Lubricant

I’ve been riding motorcycles for decades and have tried every lube product that’s come down the pike. Most have done a great job of protecting the chain but all have had the same shortcomings – the lube flings off the chain and onto the bike’s body parts when riding and the lube is sticky and attracts dust and dirt, which adds unnecessary wear to the chain and sprockets.By contrast, DuPont’s Chain Saver goes on wet but dries to a clear, almost invisible non-tacky coating that doesn’t fling off and does not attract dirt, dust or debris. It’s a very well thought-out product! Now that I’ve discovered it, I cannot imagine myself ever using anything else.Like all other spray-on chain lubes, it can be messy to apply so I use a large trash bag as a disposable tarp, covering up my rear stand, the bottom of the wheel and tire, and the cement floor underneath the tire. After lubing I toss the bag in the trash and voila! – there’s no mess. The Chain Saver takes about 20 minutes to set up but after that the bike is ready to ride. I spray on a little more after a few hundred miles then clean it off with kerosene and start afresh about every 1000 miles or so. It comes off easily when it’s time to remove it.Incidentally I also tried the liquid version of DuPont’s Chain Saver in the squeeze bottle, thinking I’d net more product because there’s no propellant, but it seemed to take a lot more lube to get the same coverage as I got with the spray version. And the per ounce cost of the liquid version is significantly higher. So, my advice is to go with the spray version.

Warranty policy

All products are backed by unlimited mileage and one (1) Year, Limited Warranty. Please read terms and conditions for full description.

Before fitting the new part, you MUST find the reason why turbocharger FAILED and CORRECT it. Fitting a new turbo will only result the same failure. Less than 10% of turbocharger failures, are due to the turbo itself, in most cases failures are caused by outside influence. Most common causes of consequential failure (NOT COVERED BY WARRANTY) are listed below. All new Kott Turbo Works products are backed by a one (1) Year Limited Warranty. The one (1) Year Limited Warranty covers all manufacturer defects. Warranty does not cover labor recovery, accommodation, or any other costs. Turbochargers must be returned for a detailed warranty inspection. Any modification to the product voids the one (1) Year Limited Warranty. The one (1) Year Limited Warranty does not cover :

Failure to provide installation documents from repair facility. (Self/parking lot installs)
Failure to perform and document scheduled maintenance on time.
Seaping/leaking oil out of compression outlet, caused by excesive BLOW BY or clogged crankcase FILTER.
Failures due to Improper installation or maintenance, restricted oil feed pipe, damaged oil pump, low oil level, metal particles or carbon present, faulty DPF filters and/or EGR valves, contaminated lubricant, oil starvation.
Using liquid gasket or sealing compounds
White deposit present on exhaust parts due to excessive engine oil burn.
Over speeding, defective intercooler and or compression piping, stuck VGT, Remap
Foreign object and physical damage, defective or dirty air filter and supply pipes.

Due to the intricacies involved in warranty process and the industry standard protocol regarding the inspection of parts and turnaround time, we will not offer free replacements prior to full inspection and analysis. To minimize potential downtime for our customers, we strongly recommend the purchase of replacement parts as a proactive measure. We kindly request your understanding in this matter.

Core return

Cores must be returned in undamaged shipping conditions, if damage occurs during shipping, due to poor packaging or other reasons we reserve the right to prorate or forfeit core refund at our discretion.

Cores must be returned within 60 days for full core refund and it has to meet all criteria, after that core refund will be at KTW discretion. Upon receiving your good core, we will issue a refund within a 1 week period. All cores are subject to inspection upon arrival. Any returned item with physical damage will result in denial of return credit or refund. The Following are examples of Turbos that will NOT be refunded:

Turbochargers: Bent or broken anything except turbine shaft. Bent, broken or damaged housing.
Core has to be sent with copy of purchase order, in order to know for which turbo we have to issue the refund, KTW won’t know who returned it, without proper documentation.
Core must be like-for-like.

We provide free return shipping using a FREE FedEx return label to return the core back to us, from most of the locations in the US (excluding Alaska, Hawaii, and Puerto Rico).

Shipping and returns

We use FedEx ground for shipping, contact us for expedited service, or other special arrangements.

We usually ship the same day, unless item is out of stock due to local in store purchase, you can call/text us at 331-888-8726 to check availability and place 12 hours hold status on item.

If your order has shipped, the return and restocking fee is 20%. Customer must pay for return shipping. Shipping from when the product was sent out is not refunded as that cost has been spent and is unrecoverable. Returns are only allowed for 14 days from post marked day, after that only store credit can be allowed at our discretion, not guaranteed.

Installation tips

Most common misdiagnosis.

Oil leaks can be caused by a variety of factors, the main factor being incorrect pressure within the compressor and turbine housings, which is usually caused by:

Blockages to the air intake filter and/or hoses.
Excessive crank case pressure (blow-by from worn piston rings/bores)
Blockages in the exhaust system
Repeated hot engine shutdowns leading to carbon deposits (coke) in the centre housing
Dirty crankcase filter
Use of silicon sealant / incorrect gasket, twisted, bent or trapped oil return pipe

Most common turbocharger failure causes on semi trucks:

Foreign object damage – Broken off engine components, e.g. valves (D13), fragments of damaged pistons or injector tips, EGR block off plates.
Oil contamination – High carbon build up present in the engine can quickly contaminate new oil, contamination of new oil while servicing.
Degrading oil – excessive temperatures or extended service intervals.
Internal engine leaks – fuel or coolant mixing with oil supply.
Turbocharger overspeeding – Engine modifications including ‘chipping’ or ‘over-fuelling, bad program installed if EGR/DPF delete was performed, worn injectors. Tear in the air hose or the hose becoming completely detached. Restrictions in the air intake filter or pipe work. Air leaks between compressor and engine.
Lack of lubrication –

1. Engine left idle for long periods, especially during cold weather
2. Oil feed pipes containing bends or kinks
3. Lack of maintenance, oil change intervals should be shortened as engine gets old.
4. Insufficient oil in the sump
5. Incorrect oil inlet gasket used leading to restriction in oil supply
6. Build-up (coking) / carbon deposits in the oil feed pipe
7. Applying silicone to the oil inlet gasket causing blockages
8. Sludge or coke build up in bearing housing from hot shutdowns
9. Failure to prime the turbo with oil before initial run